our partner ads

The World's Biggest Working Revolver



The World's Biggest  custom working revolver weighs a mere ninetynine pounds has a length of four feet two inches and stands approx one foot four inches from the butt to the top of the hammer.  When compared to a normal sized revolver as in the picture above and below, then this gun is truly a behemoth and one that can only leave you feeling awestruck! Also, check out the size of the ball shot that it fires!


The revolver is so big that it is impossible to hold up to fire, even with both hands.  So it would have to be fired and indeed loaded from a bench every time.

Impracticality over-rides any form of usefulness and the revolver is more of a showpiece, a display of skilful engineering than a practical firearm. Something like this though would be great for educating groups of people on how historic black powder firearms were used.  So from the point of view of education and history, then its a big thumbs up.


This exhibition revolver would be one hell of a talking piece and presumably a big crowd puller too.  The revolver has now been encased in a glass display box and can  be seen at trade shows and gun fairs.  When or if this revolver does a tour of the U.S.A or U.K, I will try to get any dates and post them up because it would be well worth the trip to go see this marvel of fine tolerance, scaled up engineering.


The revolver  is a fully working, exact scaled-up copy of an 1858 Remington New Model Army black powder revolver.  It can be loaded and fired in exactly the same way as the original except that the revolver needs to be supported on something substantial like half a log before it can be fired.


The recoil that the revolver delivers can only be estimated to be quite noticable, as no actual information of this has been detailed? The fact that this is a black powder firearm though would suggest that the recoil would not be enough to throw the gun into the air or off the bench but would rather just buck back a few degrees, held in situ by its weight.

The revolver was constructed by Ryszard Tobys, pictured above and below, of Czempin, Poland. The Revolver was successfully test fired on July 15th, 2002, whilst resting the end of the muzzle on half a log...as you do! As stated earlier though, sadly there is not a lot of information on the results.  If Mr. Ryzard Tobys would like to contact me though and furnish me with the details then this would be great.


The revolver has some amazing ballistic specifications with its caliber of 28mm of which is just over one inch! and each of the massive ball shot weighing 2,056 grains (4.7 oz) Most normal sized .44 caliber revolvers bullets weigh about two hundred grains by comparison, so therefore this revolver is ten times bigger.


I must remind you here that this is  a copy of a historic black powder cap ' n ' ball revolver.  Black powder revolvers had no cartridges to load up, instead the revolver was loaded by first charging up each of the cylinders six apertures with black powder, the ball  (bullet) was then positioned on top of each charged cylinder aperture and was then pressed down by the ramrod under the barrel.  A percussion cap was then placed on the firing nipples on the end of the cylinder and finally the hammer was manually cocked to fire the piece.

It was a long drawn out process to load these revolvers, the 1858 Remington New Model Army however, had a quick release cylinder and shooters used to carry preloaded cylinders that they would change over when the gun was empty.  They could do this in seconds too, just as fast as modern day shooters load up a revolver with a speed loader



Despite what has been said about this revolver on several other websites...For a start it is copy of an 1858 Remington New Model Army, it is not an 1859 Navy, it is not a Nitro Express, it is not a Colt Navy or a whole host of other misinformed things that  I have seen on the net. Also and more importantly for all gun enthusiasts.

SOURCE VIA-CLICK HERE
Share on Google Plus

About Unknown

This is a short description in the author block about the author. You edit it by entering text in the "Biographical Info" field in the user admin panel.
    Blogger Comment
    Facebook Comment

0 comments:

Post a Comment